- Clopay garage door lock installation instructions install#
- Clopay garage door lock installation instructions manual#
- Clopay garage door lock installation instructions skin#
Slide the lock arm into the rectangular slot.Ĭonfirm that it slides easily into the hole without any rubbing against the edges. Moving between screws ensures that you are tightening the lock assembly down at an even pace so that the door section does not warp from overtightening one screw side. Tighten the screws with a wrench using an alternating pattern between each screw. Press the supplied sheet metal screws into the slide locks screw cutouts.Įach slide lock manufacturer has a different screw type and configuration the assembly can use either two or four screws for one lock.Ĭonsult the locks instructions for specific fastener types and quantity.
Verify that the slide lock aligns with the screw holes, as well as with the rectangular slot for the sliding arm. Hold the slide lock up against the screw holes. These open screw holes will hold the slide lock in place. Locate the screw holes on the garage doors second section directly to the left of the tracks rectangular slot. Locate the rectangular slot on the right vertical door track inside the garage. The basic slide lock only requires a few securing screws for a safe installation and peace of mind. These internal locks provide a physical barrier for a higher level of security so that the door cannot open even if the opener activates.
Clopay garage door lock installation instructions install#
You have no obligation to purchase the product once you know the price.Īs an added precaution, you can install garage snap slide locks. Replacement keyed lock kit for standard residential wood or steel doors.Īs a result, we cannot show you the price in catalog or the product page. I would definitely use this company again and they have a variety of parts that are difficult to find.
Clopay garage door lock installation instructions manual#
Install Clopay Garage Door Keyed Lock Set Manual For Specific.A – Single or Double Set of Lock Handles 1 19’0” – 20’0” Short Emboss D L D 15’10”-19’0” Short Emboss D L D 11’6”-14’6” Short Emboss D D L 7’8”-10’0” Short Emboss D L 6’0”-7’6” Short Emboss D L 19’0” – 20’0” Long Emboss D L D 15’10”-19’0” Long Emboss D L D 11’6”-14’6” Long Emboss D D D L 7’8”-10’0” Long Emboss Note: This lock is not available for doors 14’8” to 15’8”. B) Working Non-working Option “D” - Double Set of Lock Handles (D configurations in FIG. Working Option “L” - Single Set of Lock Handles (L configurations in FIG. NOTE: All holes must be drilled from the outside through the door and insulation, if applicable, with a sharp drill bit to ensure a clean cut. You must drill lock hole patterns according to the template provided in FIG. D’s indicate the placement of double set of lock handles (“D “lock option). L’s indicate the placement of single set of lock handles (“L” lock option). B for the placement of lock hole pattern. Step L1: If lock holes are already present in your door, proceed to Step 元. The locking handle of this set goes on the right side as shown in FIG.
Clopay garage door lock installation instructions skin#
Hole Placement for Single Skin Steel Doors with “L” Handle Locks NOTE: The working set of twisted “L” handles is always placed in the holes drilled farthest left when viewing the section from the outside. The spring latches, striker plates and lock cables (Steps L12 through L16) are to be assembled after the door and track have been installed. 4 NOTE: If door is not yet installed, steps L1 through L11 should be performed while section #2 is on the sawhorses. 3 Steps L12-L17 for Spring Latch, Striker Plate, and Lock Cable p. 2 Steps L9-L11 for Optional Escutcheon Plate p. 2 Steps L7-L8 for Nonworking Set of “L” Handle Locks p. 1 Steps 元-L6 for Single Set of “L” Handle Locks p. Contents: Steps L1-L2 for Hole Placement p. If your door is going to be equipped with an automatic garage door opener, make sure that the door is always unlocked when the operator is being used. This will keep the door from moving while you are working on the lock. “L” & “D” Snap-Latch Lock Assembly Instructions IMPORTANT: If your door is already attached to an automatic garage door opener and/or operational, be sure to disengage the opener and place a C-clamp in the track just above one of the rollers before beginning work.
0 kommentar(er)
